Call & Buy Now
86-755-82451020
86-755-82451020
Auto ECU ProgrammerTMS374 ECU DECODER |
|
|
|
 |
|
Product name： TMS374 ECU DECODER |
|
Item： OS900TMS374 |
|
Color： white |
|
Spec： 2910 |
|
| Details： |
|
TMS374 ECU DECODER description This Tool is a frequency sweeper with 5V square wave output (Duty cycle 50%, effective frequency range from over 10kHz (max 50kHz) to 50Hz) .This tool can be
also considered as a MCU version of the software TMS-374 Decoder ECU. The only
difference between the two tools is that the MCU version works without a PC.
A small MCU is used to generate the pulses instead of the PC RS232 Tx line.
Manual
reaching the lowest frequency the LED goes off and the mcu stops the generation.
TMS-374 Decoder ECU info
The sweeper should work with the following ECUs:
------------------------------
Renault SIEMENS Fenix 3 and 5
------------------------------
Renault Megane 1400cc 8v
Renault Megane 1600cc 8v
Renault Megane 2000cc 8v
Renault Megane 2000cc 16V
Renault Megane Scenic 1400cc 8v
Renault Megane Scenic 1600cc 8v
Renault Megane Scenic 2000cc 8v
Renault Sefrane 2000cc 16V
Renault Laguna 2000cc 8v
Renault Laguna 2000cc 16v
Renault Espace 2000cc 8v
------------------------------
Renault SAGEM SAFIR 1 and 2
------------------------------
Renault Clio 1200cc 8V
Renault Clio 1400cc 8V
Renault Clio 1600cc 8V
Renault Clio 2000cc 16V Williams
Renault Laguna 1800cc 8V
Renault Laguna 2000cc 8V
Renault Laguna 1800cc 16V
Renault Laguna 2000cc 16V
Renault Twingo 1200cc 8V
Cut the immo data line on the ECU before re-fitting back to car.
Connect the GND line to any suitable GND on the ECU via the small grabber
Connect the Data line to the Reset pin on the EPROM via the small grabber
After powering the device on - the LED should blink twice. The sweeping process starts as
power is supplied to the device. LED ON - means there are pulses on the output. After
Press the button and the device will start sweeping, once the LED turns off your done
Power the ECU and then the sweeper, the sweeper will flash twice on power up
must be lifted or the track cut before decoding.
NOTE: If reset pin is connected to ground then it
This can be re-attached after decoding the ecu.
As a rule of thumb keep the power connected
to the ECU for a futher five minutes after the decoder
has completed the decoding process Dear customer, in addition to the TMS374 ECU DECODER product, the product is also worthy of our attention http://www.obdsvs.com/html_products/bmw-m30580.html http://www.obdsvs.com/html_products/TMS370.html http://www.obdsvs.com/html_products/711-20programmer.html http://www.obdsvs.com/html_products/908-20programmer.html http://www.obdsvs.com/html_products/912-9S12-9S12X-%20Programmer.html http://www.obdsvs.com/html_products/CAN-BDM-CAS3-9S12.html |
|
| ←[Previous：OS900CARPROG] | [Next：OS900PV]→ |
| Related Products : |
|
|
|
|
||||||||
|
|
|
|
